ORMECON RAD 7000 c

Rinse Aid for ORMECON CSN Classic Immersion Tin Processes

-------------------ORMECON RAD 7000 c 用于ORMECON CSN 經典浸錫工藝的漂洗助劑

CHARACTERISTICS【簡介】

ORMECON RAD 7000 C is an aqueous, alkaline, liquid concentrate used to assist in the removal of residueson PCB (printed circuit boards) following the initial water rinsing of ORMECON CSN 7004 immersion tinbath. When diluted with deionized water the ORMECON RAD 7000 C neutralize acidic residues left on the PCB from the immersion tin bath, significantly reducing ionic contamination levels on the boards. It can be used in either spray or immersion applications. ORMECON RAD 7000 C is free rinsing and completely compatible with the entire line of CSN Classic lmmersion Tin process chemistries.ORMECON RAD 7000 C是一種水性，堿性，液體濃縮物，用于在ORMECON CSN 7004浸泡錫槽初始水沖洗后協助去除PCB(印刷電路板)上的殘留物。當用去離子水稀釋時，ORMECON RAD 7000 C可以中和浸泡錫槽中留在PCB上的酸性殘留物，顯著降低電路板上的離子污染水平。它可以用于噴霧或浸泡應用。ORMECON RAD 7000 C是免費漂洗，完全兼容整個系列的CSN經典lmmersion錫工藝化學。

OPERATING CONDITIONS【操作參數】

Horizontal Range Nominal

Concentration（濃度）1.0 to 25% by volume 5.0%

Temperature （溫度）40 to 60 C (104 to 140°F) 50°C (122 °F)

MAKE-UPPROCEDURE【組成】

Before handling any of the products referred to in this data sheet ensure all relevant Safety Data Sheets have been read and understood. 在處理本數據表中提到的任何產品之前，確保已閱讀和理解所有相關的數據表。

To make up the ORMECON RAD 7000 Post Treatment Rinse Aid add the required amount of ORMECONRAD 7000 C to heated, recirculating, water. 為配制ORMECONRAD 7000處理后漂洗助劑，將所需量的ORMECONRAD 7000 C加入加熱的循環水中。

OPERATION【操作】

PCB panels must be thoroughly rinsed with Dl water prior to entering the ORMECON RAD 7000 C rinse aid.DO NOT use ORMECON RAD 7000 C immediately following ORMECON 7004 CSN immersion tin bath without a water rinse. Typical dwell times in ORMECON RAD 7000C are between 20 and 90 seconds. ORMECON RAD 7000 C is always followed by thorough water rinsing to ensure removal of the rinse aid solution from the PCB board surface. Deionized water should be used in the final rinse to achieve the required ionic cleanliness. ORMECON RAD7000 C treatment is especially recommended for complex board designs, as well as blind vias and solder mask plugged holes. 在進入ORMECON RAD 7000 C沖洗助劑之前，PCB板必須用Dl水徹底沖洗。在沒有水沖洗的情況下，不要在ORMECON 7004 CSN浸泡錫浴后立即使用ORMECON RAD 7000c。ORMECON RAD 7000C的典型停留時間在20到90秒之